Drone Surveying with the Xplorer

How Does Drone Surveying Work?
Drone surveying, often called photogrammetry, is the process of capturing hundreds of overlapping, high-resolution aerial photos and turning them into accurate 2D maps, 3D models and elevation data.
Here is the idea in plain terms. Every point on the ground shows up in several photos, each taken from a slightly different position. Processing software finds those shared features, works out exactly where each photo was taken, and uses that geometry to rebuild the ground in three dimensions. Tie the result to a handful of precisely surveyed points on the ground, and you have a map you can measure from with confidence.
Traditional ground surveys are still the gold standard for individual points, but measuring an entire site one shot at a time is slow, and every shot is another chance for error. A drone captures millions of measurements in a single flight. As drones have become more capable and easier to access, aerial surveying has become the first choice for a growing share of mapping work.
A few terms you’ll see in this article
GSD (ground sample distance): how much ground one image pixel covers. A 2 cm GSD means each pixel represents 2 cm on the ground. Smaller is more detailed.
GCP (ground control point): a target on the ground whose position is measured with survey-grade GNSS. GCPs lock the map to real-world coordinates.
Checkpoint: a surveyed target that is deliberately left out of processing. Comparing it to the finished map tells you how accurate the map really is.
Orthomosaic: a single, distortion-corrected aerial image of the whole site, stitched from all the photos. Distances measured on it are true to scale.
Point cloud: millions of 3D points, each with a position and a color, that together describe the surface of the site.
DSM and DTM: elevation models. A DSM (surface model) includes buildings and trees. A DTM (terrain model) is the bare earth underneath.
RTK (real-time kinematics): a correction technique that improves GNSS accuracy from meters to about a centimeter.
Rover and base: a rover is the GNSS receiver you carry on a pole to measure points. A base is a receiver set up over a known point that sends corrections. Many areas have network RTK services that act as the base, so you only need the rover.
Coordinate system: the reference frame and units your map is delivered in, such as a State Plane zone in US survey feet. Every tool on the project needs to use the same one.
What is Drone Surveying used for?
Drone surveying is used across construction, mining, utilities, urban planning, agriculture, research and more. The common thread is that teams need reliable spatial data to make decisions. Typical jobs include:
Topographic mapping: understanding the shape of a site before design or construction begins.
Volume calculations: measuring stockpiles, or the cut and fill on an earthworks project.
Measurements: taking precise distances, areas and elevations from one point to another, without walking the site.
Digital twins: building an accurate 3D model of a site or structure for ongoing planning.
Drainage and water flow: studying how water moves across a crop field or development site.
The Xplorer Surveying Workflow
Photogrammetry has a reputation for being technical, but the workflow comes down to five steps: plan, set out ground control, fly, process and deliver. The details below follow the same process our team uses, and the one we’ll share with you when you start flying.
First, choose how your map gets georeferenced
Before we start, one decision shapes everything else: how the map gets tied to real-world coordinates. The Xplorer supports two approaches.
GCP-only. The Xplorer’s standard GPS tags each photo with an approximate position, and the map’s accuracy comes from ground control. A moderate site typically needs 8 to 12 GCPs. No correction service is needed on the aircraft.
RTK. The Xplorer’s RTK GNSS records the camera’s position to within a few centimeters at the moment each photo is taken. Those positions do most of the georeferencing, so you typically only need 3 to 5 GCPs, mainly to lock down elevation. That means less time setting and measuring targets on every job.

Either way, you also set out a separate group of checkpoints to prove the final accuracy. More on that in the accuracy section below.
Step 1: Plan
Confirm the project requirements. Before anything else, agree with the client on the site boundary, the deliverables, the accuracy target and the coordinate system. Use that same coordinate system in your field app, your processing software and your deliverables. A mismatch between tools is one of the most common causes of a map that lands a meter off.
Pick your lens. The Sony ILX-LR1 on the Xplorer takes interchangeable prime lenses, and the choice affects both detail and accuracy.
A 24 mm lens is a good choice for general mapping, topographic surveys and earthwork. It covers about 45% more ground per flight line than the 35 mm, and its wider view improves vertical accuracy. A 35 mm lens gives finer visual detail at the same height and reduces building lean in dense built-up areas.
Plan the flight. Plan the flight in the Arcsky Control app, either on the desktop version or directly on the controller. Import a KML file or draw the survey area, extending it at least one flight line past the site boundary on every side. Choose your lens and flying height, then set overlap and camera settings. A good starting point is 80% front overlap and 70% side overlap, with a little more over low-texture surfaces like vegetation, water, sand or fresh pavement. Arcsky Control works out the flight lines, photo spacing and flight time, so you can estimate how many flight batteries you’ll need. If you’re flying RTK, add a few lines perpendicular to the main pattern to strengthen the elevation solution.


Plan your ground control. Spread GCPs evenly so they enclose the site: one near each corner, one near the middle, and extras along long edges. Plan 8 to 12 for a GCP-only survey or 3 to 5 with RTK. Then add checkpoints between them, covering the high and low parts of the site and any areas the client cares most about.
Step 2: Set Out Your Ground Control
Lay out your targets and secure them. A high-contrast checkerboard target about 60 cm (24 in) across, with a crisp center, works well at the GSDs in this workflow. Photograph each one with its label.
Measure the exact center of each target with a GNSS rover, such as the Emlid Reach RS4 on network RTK corrections. Before you start, check in on a known survey point to confirm your setup is correct. Then survey every target once before the flight and again after it. The two measurements should agree within 2 to 3 cm, which gives you confidence in every point that goes into the map.
If there’s no network RTK coverage at your site, the RS4 can also be set up as a local base to provide corrections.

Step 3: Fly
Before flying, make sure your camera is set appropriately for the conditions. Within Arcsky Control, you can do this directly on the Sony ILX-LR1 payload.
Focus locked at infinity and stabilization off, recommended so the camera’s geometry stays identical from photo to photo. You can also use auto-focus if you'll be flying lower to the ground.
Shutter priority at 1/2000 s or faster to freeze motion. Use 1/3200 s with the 35 mm lens at low altitude.
Aperture between f/5.6 and f/8 for sharp images across the frame.
Fixed daylight white balance so colors match across the whole map.
After camera settings are set and your survey mission is planned, take off and set the flight mode to AUTO. The Xplorer will fly the survey pattern automatically, and the camera mount is vibration-isolated to keep images sharp. For the best results, fly between mid-morning and mid-afternoon to avoid long shadows, and try to avoid partly cloudy days that can cause wide exposure changes mid-flight. If you’re using RTK corrections, confirm the aircraft has an RTK fix before takeoff.
Hot-swappable batteries let you stop partway through the mission and install fresh batteries. Take off again and repeat until the mission is complete. The Xplorer always continues where it last left off, unless configured otherwise.
Check your data before you leave. Before picking up targets, confirm the image count matches the plan, spot-check a few photos at full zoom for sharpness, and make sure every target is visible. A reflight is easy while you’re still on site.
Step 4: Process
Processing turns a folder of photos into measurable products. You can use industry-standard tools for this workflow.
Agisoft Metashape or Pix4D builds the map. It aligns the photos, then you mark each GCP in the images where it appears so the model locks onto real-world coordinates. Checkpoints stay switched off so they remain an honest test. The software refines the camera calibration, removes weak matches, and then produces the dense point cloud, the surface model (DSM) and the orthomosaic.


Terrasolid sorts the point cloud. It classifies each point as ground, low, medium or high vegetation, building, or noise, then builds a bare-earth terrain model (DTM) and contours from the ground points. One honest caveat: photogrammetry can only see what the camera sees, so ground under thick vegetation is estimated rather than measured. We note this on every deliverable.
Step 5: Deliver
Every deliverable is exported in the project coordinate system, ready to open in GIS or CAD software, along with a short readme listing the coordinate system, flight date, GSD and accuracy summary. A typical package includes:
Deliverable | Format | What it’s for |
Orthomosaic | GeoTIFF or ECW | A true-to-scale aerial image for measuring, planning and presentations |
Surface model (DSM) | GeoTIFF | Elevations including structures and vegetation |
Bare-earth terrain model (DTM) | GeoTIFF | Ground elevations for design, drainage and earthworks |
Classified point cloud | LAS or LAZ | Full 3D data, sorted into ground, vegetation, buildings and more |
Contours | DXF, DWG or SHP | Ready-to-use linework for CAD at the client’s interval |
Control points | CSV | Every GCP and checkpoint, with coordinates |
Accuracy and processing reports | Documented proof of the map’s quality |
Accuracy Metrics Explained
Accuracy is the question every surveyor asks first, so here’s how we answer it.
We measure it, we don’t estimate it. Accuracy is reported only from checkpoints: surveyed points that were never used to build the map. Comparing their surveyed positions with their positions on the finished map gives a root mean square error (RMSE), stated separately for horizontal and vertical. Under the ASPRS standard, the accuracy of the ground survey itself is included in that number too, so the result reflects the whole process.
How many checkpoints? For internal quality checks, 5 to 10 well-placed checkpoints give a reliable picture. If your client needs a formal ASPRS accuracy report, the standard requires at least 30.
Two things set the limit: image detail (GSD) and the quality of your ground control. As a rule of thumb, horizontal accuracy lands around 1 to 2 times the GSD and vertical around 1.5 to 3 times the GSD. With the 24 mm lens at 120 m (a 1.9 cm GSD) and network RTK ground control, that points to roughly 2 to 4 cm horizontal and 3 to 6 cm vertical.
Interestingly, flying lower for a finer GSD doesn’t automatically make the map more accurate. At around 1.9 cm, the imagery is already well matched to the 1 to 2 cm accuracy of RTK ground control. Fly lower when you need more visual detail, not as a shortcut to accuracy.
Xplorer Mapping Workflow Example
We tested the full Xplorer mapping workflow with Vertical Aspect in October 2026 at a stadium site in Kansas City with 31 permanently marked, precisely surveyed control points.


Using both a local base station and a network RTK (NTRIP) connection, we were able to maintain an RTK fix status throughout the flights, providing accurate geotagging data.
Images were later processed with Agisoft Metashape to create a final report and deliverables, including GeoTIFF, LAS files, and a full PDF survey report.
With the Xplorer's hot-swap batteries, we were able to capture multiple data sets using only two sets of batteries, charging each idle set with a small generator while the others flew.
Key Takeaways
Drone photogrammetry has become a practical, survey-grade tool for construction, earthworks, mining, land development and many other industries. The results come down to a disciplined workflow: a clear plan, well-measured ground control, consistent camera settings and honest accuracy reporting from checkpoints. Get those right, and a single day in the field can produce a complete, measurable model of a site that would take far longer to survey on foot.
Why Xplorer?
A high-resolution camera with lenses that grow with you. The Xplorer carries the Sony ILX-LR1, a full-frame, 61-megapixel mapping camera. It takes interchangeable lenses, so you’re never locked into one setup. Fly a 24 mm lens for efficient topographic mapping, switch to a 35 mm lens for fine detail in built-up areas, and add new lenses as new kinds of work come your way.
One app for the whole job: Arcsky Control. Plan the mission, watch the live flight view and adjust camera settings, all from one app. You don’t have to switch between separate apps for planning, flying and the camera, and there are fewer places for a setting to slip.
RTK-capable GNSS for survey-grade positioning. With RTK, the Xplorer records the camera’s precise position at the moment each photo is taken. That means 3 to 5 ground control points instead of 8 to 12, and less time on site for every job.
Long flights, with hot-swappable batteries for bigger sites. With the Sony ILX payload, the Xplorer flies for up to 30 minutes and easily covers over 300 acres of survey area in a single flight. For larger sites, change batteries without powering down the drone. There’s no rebooting and no waiting for systems to come back online, so you’re back in the air within moments.

Ready for LiDAR when you are. The Xplorer can carry payloads of up to 2 kg (4.4 lb), including LiDAR sensors. Start with photogrammetry today. If your work moves under tree cover or onto complex structures later, add a LiDAR payload instead of buying a new aircraft.
Ready to fly in two minutes. Setup takes about two minutes, so more of your day goes to flying and less to assembly.
American-built, NDAA compliant. Designed and assembled in Austin, Texas, the Xplorer meets NDAA requirements and is backed by a team right here in the US. As drone regulations evolve, you can count on your equipment and the people who support it.
Ready to see it in action?
Whether you’re mapping your first site or looking to cut field time on the jobs you already do, the Xplorer makes survey-grade photogrammetry straightforward. To see the full workflow with a demo, contact info@arcskytech.com.